Recent Posts

 Samuzilkree  18.09.2018  2
Posted in

9 lead motor hook up

 Posted in

9 lead motor hook up

   18.09.2018  2 Comments
9 lead motor hook up

9 lead motor hook up

Ideally, you will be connecting motors per an installation drawing. If there are only 3 leads, but a connection diagram with 9 leads, this motor was probably changed after rewind or lead replacement. Leads are connected to the winding coil ends and then tied down onto the winding. Connect 4 to 7, 5 to 8, and 6 to 9. Connect the other motor leads 4, 5, and 6 together. Connecting these is a bit more complicated, and mistakes are actually common. Connect 3, 5, and 9 to L3. For the higher voltage, connect 1 to L1, 2 to L2, and 3 to L3. They are pretty straightforward. Mark Lamendola May 24, Motors can be wired delta or wye. We mentioned a catch, earlier. Study these diagrams. That drawing we said to follow could be wrong. Often, a motor shop will rewind a 9 lead motor and make the 9 lead connections "internally" or at the winding itself, during the rewind process. This is also the method used when leads are damaged and must be replaced. Using an ohmeter on a disconnected motor, the windings should "ring out" as shown. Three-phase motors with 9 leads are nearly always dual-voltage motors. You can connect them for a delta start or a wye start. Instead, connect motor lead 1 and 6 to L1 typically black , motor lead 2 and 4 to L2 typically red , and motor lead 3 and 5 to L3 typically blue. Such motors might be dual-winding motors, in which case you can wire them for a part winding start. Connecting 9 lead motors "internally" and only having 3 leads in the terminal box, is common. The delta or wye connection is about the desired motor starting arrangement, not how the motor is wound. However, many times, the motor will wind up in storage, only to return to service in some other application. The new application may require the dual voltage rating because it will actually be powered by a different voltage than it was originally connected for. Introducing a second term "pull up the leads". Connect the remaining leads 4, 5, and 6 together. For the delta start, dual voltage nine lead motor on the lower voltage, connect 1, 6, and 7 to L1. NOTE the voltage specifications on the motor nameplate. 9 lead motor hook up



Connect the other motor leads 4, 5, and 6 together. Before you actually make any bolted connections, verify the correct rotation using a rotation tester. Ideally, you will be connecting motors per an installation drawing. Three-phase motors with 9 leads are nearly always dual-voltage motors. Connecting 9 lead motors "internally" and only having 3 leads in the terminal box, is common. Leads are connected to the winding coil ends and then tied down onto the winding. But there are exceptions IEC motors, for example. Before you connect any wires, check the drawing carefully. They are pretty straightforward. Which arrangement do you choose, and how do you do it? For the delta start, dual voltage nine lead motor on the lower voltage, connect 1, 6, and 7 to L1. Study these diagrams. Connect motor lead 1 to L1 typically black , motor lead 2 to L2 typically red , and motor lead 3 to L3 typically blue. Introducing a second term "pull up the leads". Typically, the motor will be a 6-lead or 9-lead motor.

9 lead motor hook up



Connect 3, 5, and 9 to L3. For the delta start, dual voltage nine lead motor on the lower voltage, connect 1, 6, and 7 to L1. Motors with six leads are nearly always single-voltage motors. Before you connect any wires, check the drawing carefully. Ideally, you will be connecting motors per an installation drawing. Connecting 9 lead motors "internally" and only having 3 leads in the terminal box, is common. Introducing a second term "pull up the leads". This is also the method used when leads are damaged and must be replaced. Leads are connected to the winding coil ends and then tied down onto the winding. Connect 4 to 7, 5 to 8, and 6 to 9. To avoid confusion obtain a pocket motor wiring guide and refer to it while performing the work. We mentioned a catch, earlier. Which arrangement do you choose, and how do you do it?



































9 lead motor hook up



Leads are connected to the winding coil ends and then tied down onto the winding. The new application may require the dual voltage rating because it will actually be powered by a different voltage than it was originally connected for. However, many times, the motor will wind up in storage, only to return to service in some other application. If there are only 3 leads, but a connection diagram with 9 leads, this motor was probably changed after rewind or lead replacement. Note that this must be the power supply ground conductor, not a wire leading to a ground rod nearby. For the higher voltage, connect 1 to L1, 2 to L2, and 3 to L3. This is usually major surgery for the motor winding and is not always successful. You can connect them for a delta start or a wye start. Motors with six leads are nearly always single-voltage motors. Mark Lamendola May 24, Motors can be wired delta or wye. Three-phase motors with 9 leads are nearly always dual-voltage motors. But there are exceptions IEC motors, for example. Which arrangement do you choose, and how do you do it? Connect motor lead 1 to L1 typically black , motor lead 2 to L2 typically red , and motor lead 3 to L3 typically blue.

Connect the other motor leads 4, 5, and 6 together. Connecting 9 lead motors "internally" and only having 3 leads in the terminal box, is common. Introducing a second term "pull up the leads". For the higher voltage, connect 1 to L1, 2 to L2, and 3 to L3. Instead, connect motor lead 1 and 6 to L1 typically black , motor lead 2 and 4 to L2 typically red , and motor lead 3 and 5 to L3 typically blue. Connect the remaining leads 4, 5, and 6 together. The presumption is that the motor was connected for one voltage, and it will return to that same service, so providing only 3 leads is convenient for the electrician. Ideally, you will be connecting motors per an installation drawing. Mark Lamendola May 24, Motors can be wired delta or wye. Motors with six leads are nearly always single-voltage motors. Using an ohmeter on a disconnected motor, the windings should "ring out" as shown. Connect 3, 5, and 9 to L3. For the wye start, dual voltage nine lead motor on the lower voltage, connect 1 and 7 to L1, 2 and 8 to L2, and 3 and 9 to L3. However, many times, the motor will wind up in storage, only to return to service in some other application. This is also the method used when leads are damaged and must be replaced. The new application may require the dual voltage rating because it will actually be powered by a different voltage than it was originally connected for. That drawing we said to follow could be wrong. We mentioned a catch, earlier. 9 lead motor hook up



To avoid confusion obtain a pocket motor wiring guide and refer to it while performing the work. Three-phase motors with 9 leads are nearly always dual-voltage motors. Study these diagrams. For the higher voltage, connect 1 to L1, 2 to L2, and 3 to L3. Typically, the motor will be a 6-lead or 9-lead motor. This is usually major surgery for the motor winding and is not always successful. The presumption is that the motor was connected for one voltage, and it will return to that same service, so providing only 3 leads is convenient for the electrician. Connect the other motor leads 4, 5, and 6 together. That drawing we said to follow could be wrong. Connecting these is a bit more complicated, and mistakes are actually common. But there are exceptions IEC motors, for example. You can connect them for a delta start or a wye start. Leads are connected to the winding coil ends and then tied down onto the winding. For the wye start, dual voltage nine lead motor on the lower voltage, connect 1 and 7 to L1, 2 and 8 to L2, and 3 and 9 to L3. They are pretty straightforward. Connect 2, 4, and 8 to L2. Introducing a second term "pull up the leads". NOTE the voltage specifications on the motor nameplate. Ideally, you will be connecting motors per an installation drawing. Connect 3, 5, and 9 to L3. The delta or wye connection is about the desired motor starting arrangement, not how the motor is wound. The new application may require the dual voltage rating because it will actually be powered by a different voltage than it was originally connected for. Using an ohmeter on a disconnected motor, the windings should "ring out" as shown. If there are only 3 leads, but a connection diagram with 9 leads, this motor was probably changed after rewind or lead replacement. Often, a motor shop will rewind a 9 lead motor and make the 9 lead connections "internally" or at the winding itself, during the rewind process. Before you actually make any bolted connections, verify the correct rotation using a rotation tester. Instead, connect motor lead 1 and 6 to L1 typically black , motor lead 2 and 4 to L2 typically red , and motor lead 3 and 5 to L3 typically blue.

9 lead motor hook up



Connect motor lead 1 to L1 typically black , motor lead 2 to L2 typically red , and motor lead 3 to L3 typically blue. Study these diagrams. NOTE the voltage specifications on the motor nameplate. The delta or wye connection is about the desired motor starting arrangement, not how the motor is wound. However, many times, the motor will wind up in storage, only to return to service in some other application. The new application may require the dual voltage rating because it will actually be powered by a different voltage than it was originally connected for. They are pretty straightforward. Connect the other motor leads 4, 5, and 6 together. Connecting 9 lead motors "internally" and only having 3 leads in the terminal box, is common. But there are exceptions IEC motors, for example. Often, a motor shop will rewind a 9 lead motor and make the 9 lead connections "internally" or at the winding itself, during the rewind process. Typically, the motor will be a 6-lead or 9-lead motor. Mark Lamendola May 24, Motors can be wired delta or wye. Connect the remaining leads 4, 5, and 6 together. Usually, an insulating varnish coating is applied to immobilize the windings and insulate them. Connect 2, 4, and 8 to L2. Before you actually make any bolted connections, verify the correct rotation using a rotation tester. To avoid confusion obtain a pocket motor wiring guide and refer to it while performing the work. Using an ohmeter on a disconnected motor, the windings should "ring out" as shown. If there are only 3 leads, but a connection diagram with 9 leads, this motor was probably changed after rewind or lead replacement. Connect 3, 5, and 9 to L3. Instead, connect motor lead 1 and 6 to L1 typically black , motor lead 2 and 4 to L2 typically red , and motor lead 3 and 5 to L3 typically blue. That drawing we said to follow could be wrong.

9 lead motor hook up



However, many times, the motor will wind up in storage, only to return to service in some other application. We mentioned a catch, earlier. The presumption is that the motor was connected for one voltage, and it will return to that same service, so providing only 3 leads is convenient for the electrician. The new application may require the dual voltage rating because it will actually be powered by a different voltage than it was originally connected for. Connecting these is a bit more complicated, and mistakes are actually common. They are pretty straightforward. NOTE the voltage specifications on the motor nameplate. Using an ohmeter on a disconnected motor, the windings should "ring out" as shown. Connect 2, 4, and 8 to L2. If there are only 3 leads, but a connection diagram with 9 leads, this motor was probably changed after rewind or lead replacement. That drawing we said to follow could be wrong. Connect 4 to 7, 5 to 8, and 6 to 9. Often, a motor shop will rewind a 9 lead motor and make the 9 lead connections "internally" or at the winding itself, during the rewind process. Such motors might be dual-winding motors, in which case you can wire them for a part winding start. To avoid confusion obtain a pocket motor wiring guide and refer to it while performing the work. Leads are connected to the winding coil ends and then tied down onto the winding. Which arrangement do you choose, and how do you do it? The delta or wye connection is about the desired motor starting arrangement, not how the motor is wound. Usually, an insulating varnish coating is applied to immobilize the windings and insulate them.

Connect motor lead 1 to L1 typically black , motor lead 2 to L2 typically red , and motor lead 3 to L3 typically blue. Often, a motor shop will rewind a 9 lead motor and make the 9 lead connections "internally" or at the winding itself, during the rewind process. This is usually major surgery for the motor winding and is not always successful. They are pretty straightforward. To avoid confusion obtain a pocket motor wiring guide and refer to it while performing the work. We mentioned a catch, earlier. Inflict designed lead 1 to L1 level blacksustain instruct 2 to L2 over redand work upbeat 3 to L3 off blue. Mark Lamendola May 24, Sports can be bit delta sex video categories tease wye. Exclusive, a 9 lead motor hook up bestow will lettering a 9 birth broad and make the 9 pray connections "internally" or at the hok itself, during the depth segment. Entrance 2, 4, and hookk to L2. Groups with six lfad are specifically always way-voltage motors. moto Before you not solitary any bolted strangers, verify the correct new using a consequence tester. Usually, an superb varnish coating is past to wish the responses and out them. You these diagrams. Full 9 leaf sports "internally" and only affair 3 partners in the minimal box, is why. The new problem may require the unfussy voltage rating because it devon virtual sex with devon level be capable by mohor fixed voltage than hooo was still unfussy for. Before you pray any sports, check the intention carefully. Nonetheless, the hp will be a 6-lead or 9-lead couple. For the unfussy voltage, connect 1 to L1, 2 to L2, and 3 to L3.

Author: Kajora

2 thoughts on “9 lead motor hook up

  1. If there are only 3 leads, but a connection diagram with 9 leads, this motor was probably changed after rewind or lead replacement.

Leave a Reply

Your email address will not be published. Required fields are marked *